To change the default reading back to the average salt, start by pressing the ‘Diagnostics’ button two times. Continue moving the switch up to ‘Super Chlorinate’ and back to ‘Auto’ until the display reads ‘AL-0’. It takes about 30 seconds for the unit to settle back on the default reading.

How do you change the salt reading on Aqua Rite?

To change the default reading back to the average salt, start by pressing the ‘Diagnostics’ button two times. Continue moving the switch up to ‘Super Chlorinate’ and back to ‘Auto’ until the display reads ‘AL-0’. It takes about 30 seconds for the unit to settle back on the default reading.

How do you calibrate a Hayward Aqua plus salt cell?

Turn Salt System Off and On With the pump running, take the power switch down to the “Off” position, and then back up to “Auto”. You should hear a click within 10 or 15 seconds. When you do, press the diagnostic button five times in a row. The system will go through a recalibration process.

What percentage should my salt cell be set at?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

What happens if salt level is too high in pool?

Having too much salt in your pool water can result in unnecessarily increasing chemical expenses. But having too little salinity restricts the amount of chlorine being generated and can lead to algae and bacteria growth.

Why is my pool salt level low?

The salt in your pool/spa is constantly recycled and the loss of salt throughout the swimming season should be minimal. Water loss is due primarily to the addition of water because of splash out, backwashing and/ or overflowing because of rain. Salt does not wear out or evaporate.

What should my Hayward salt generator be set at?

The ideal salt level is between 2700-3400 ppm (parts per million) with 3200 ppm being optimal. If the level is low, determine the number of gallons in the pool and add salt according to the chart on page 4. A low salt level will reduce the efficiency of the Aqua Rite® and result in low chlorine production.

How do you get the chlorine level up in a saltwater pool?

How do you raise the free chlorine in a salt-water pool? You can use granular shock or shock pods in your saltwater pool. Just make sure that you use your long-handled pool brush to disperse any shock that settles to the bottom.

What setting should my salt generator be on?

Try to maintain a consistent salt level of between 2,700 parts per million (ppm) and 3,400 ppm, with 3,200 ppm being ideal.

How many hours a day should a salt water pool pump run?

The average pool system needs to run anywhere between 4-10 hours so you will have to gauge it yourself though testing over time.

Article first time published on

Should chlorinator be full of water?

The saltwater chlorinator needs a sufficient flow of water for effective operation. A dirty skimmer basket, clogged or dirty filter, and a clogged pump strainer, can cause insufficient water flow for the chlorinator to produce less chlorine.

What should my chlorinator read?

On a Hayward Salt Chlorinator, your salt reading should be between 2,700 – 3,400 PPM (parts per million) with the optimum level of 3,200 PPM.

How do you reset the salt level on a Hayward Aqua Logic?

You must reset the system by entering the ‘Diagnostic Menu’ and then hitting the right arrow key once and then pushing the plus (+) key once. This should reset the light and message. Lastly, follow the instructions on page 16 to reset the salt level after cleaning the cell.

How do I reset my Hayward Salt Cell inspect cell?

Reset AquaRite Salt Chlorination Inspect Cell Light If the Inspect Cell Light is the only LED light flashing, then you can reset it by simply holding down the diagnostic button for 3 seconds, then release. The Inspect Cell indicator will now reset and will later come back on after another 500 hours of use.

How many bags of salt do I need for my pool?

How much salt to add to the pool? To reach the initial salt level recommended by the salt system manufacturer (usually 2400-3200 ppm), you will need to add about 200 lbs of pure pool grade salt (NaCl), per 10,000 gallons of water.

Can you put too much salt in a saltwater pool?

The salt level in your swimming pool should be 3,000 ppm (parts per million). Over-salting will not damage your pool system, but will create salty-tasting water. Highly excessive Salinity levels (over 6,000 ppm) will cause corrosion damage to metallic equipment, such as ladders and handrails.

How many bags of salt do I need for a 12000 gallon pool?

Current Salt LevelSalt Needed8,000 Gallon Pool12,000 Gallon Pool1,000147 lbs.220 lbs.2,00080 lbs.120 lbs.3,00013 lbs.20 lbs.

What setting should my pool chlorinator be on?

Chlorine Feeders: For each 5000 gallons of pool water, add one 3″ chlorine tablet, more or less. Choose a mid-point setting on the 1-10 dial. The higher the setting, the greater the dissolution rate. A setting of 5 may be too high, and it depends on the number of tablets in the feeder.

How many pucks are in a Hayward chlorinator?

Your CL-220 holds up to 18 large (3″ diameter) tablets (about 9 lbs.) and has a dial type control valve to regulate the rate of water flow through the chlorine feeder. This large capacity feature, under normal conditions, should provide a minimum of two weeks chlorination for large pools.

How often do you add salt to a saltwater pool?

There is no set timeframe of when you need to add salt to your pool. Because salt does not dissipate from your water, the only time you would add salt to your pool is when you add fresh water or after heavy rain that dilutes salinity levels.

How do I know if my salt generator is working?

The easiest way to ascertain if the chlorinator is working is to make sure the cell is clean by checking the needle or production lights. Ensure there is enough salt in the pool. On the chlorinator box there should be a light or dial that indicates it is working.

Do you shock salt water pools?

Should you add shock to a salt water pool? It’s absolutely okay to shock your salt water pool, and is actually pretty important! … Running your pool’s super-chlorinate feature too often is hard on the motor and will cause it to wear out faster.

Why is my salt generator not producing chlorine?

Salinity. Chlorine generators need salt to produce chlorine and can’t do so if the amount of salt in the water is too low. The desired salinity level in a saltwater pool is between 2,500 and 3,500 ppm. … If your salinity is below 2,500 ppm, the generator will not be able to produce chlorine.

Why is my salt water pool pH always high?

An unnaturally high pH level in your salt water pool could be a sign that your salt cell has been shortened due to running for an overly long period of time. Check the level of your cyanuric acid to be sure. The level should be between 80 and 100 ppm.

Will baking soda lower chlorine level in pool?

Chlorine works most efficiently in water with a neutral pH level between 7.4-7.6. If the pool is too alkaline, or more than a pH of 8.0, the efficiency is less than 20 percent. … To raise your pH levels, it can be as simple as adding seven to nine pounds of baking soda to your pool water.

What happens if you pee in a saltwater pool?

All forms of aquatic life pee in the ocean with no adverse effects to the marine environment. Urea in the ocean actually helps feed plant life, so there is a “system balance” present that is not found in swimming pools.

How many pounds of salt do I need for a 20000 gallon pool?

Therefore, if you have a 20,000 gallon pool and want to determine how much salt you’ll need to buy, you would use the formula “30/1,000 x 20,000”, which equals 600. Meaning, the pool would require approximately 600 lb of salt.

Why is my salt water pool cloudy?

Just like a chlorine-based pool, saltwater pools turn cloudy when chemicals are not balanced. You need to ensure that all chemicals are balanced all the time to avoid cloudy water and growth of algae. The major causes of cloudiness are chlorine, pH, Salinity, total alkalinity, cyanuric acid, and calcium hardness.

Is it OK to run pool pump 24 hours a day?

The size of your pool, the efficiency of your pump and filter, and how dirty your pool is are just some of the factors you need to consider. Nevertheless, most pool cleaning professionals would advise against running a pool pump for more than 8 hours a day.

How long should I run my pool pump after adding salt?

To add salt, turn on your filter pump and add the salt directly to your pool water. Use a brush to help the salt dissolve and to prevent the salt from piling up on the bottom of your pool. Run your pump for 24 hours to help distribute the salt evenly throughout your pool.

How long does a saltwater pool pump last?

Your pool pump should be replaced anywhere between 8 to 15 years depending on the quality, and a full replacement may cost over $800. Your pool pump is the “heart” of your swimming pool as it circulates water throughout, bringing water through the filtration and heating systems.